下面我介紹一下如何掌握和使用機械密封平面研磨技術:
首先我們要制作一塊厚度為35mm,直徑為300mm的圓形平面研磨板,材質為球墨鑄鐵。 機械密封由于他的特殊性,非常容易在使用過程中受到破壞。
機械密封失效后,如果是膠圈失效,將其更換即可。其他泄漏,有時可通過調整靜環座等予以消除,但如果其密封端面損壞而造成的失效,則必須要重新更換密封。在機械密封失效中,端面損壞這種失效形式大約占機械密封用量的70%以上,它不但給我們造成了極大的浪費,同時也嚴重影響我們的正常生產。機械密封研磨技術,就是通過對失效端面的研磨,恢復其端面密封性能,這項技術不僅給我們節省了大量資金,同時也為生產的平穩運轉提供了條件保證。
機械密封端面要求精度*,一般應≤0.01以上。如果機械密封端面損壞,其表面粗糙度要達到0.05以上,遠遠不能滿足密封面的要求,因此會(huì )使密封失效。這時,在一般情況下,我們只有通過更換新密封,來解決泄漏問題,有時因為操作原因,一套機械密封使用壽命極短,這樣不但造成極大的浪費,如果供貨不及時,還將影響我們的正常生產。如果我們掌握了機械密封研磨技術,通過對機械密封失效端面的研磨,使機械密封失效面重新恢復其表面粗糙度≤0.01,也就恢復了其密封性能,安裝后即可正常使用,這樣我們不但解決了大量的資金,還可以及時恢復正常生產。
機械密封平面研磨工作原理:
在使用時,我們先將平面研磨板放在一個牢固的平臺上,用棉紗將其表面擦拭干凈。根據待研磨件的大小,在研磨板中心滴10~30mL的汽油。將待研磨面用棉紗擦拭干凈,之后在待研磨面上涂上0.2~0.4的金剛研磨膏,將研磨膏均勻地分布在研磨面上。向下用力將研磨件壓在平面研磨板上,均勻地使研磨件做“8”字型運動,直至將研磨面研磨至達到要求為止。
金嶺機床(傳承長沙二機床廠)創(chuàng )建于1956年,是我國原機械部定點車床生產廠家、國 有中一型企業,現為國家高新技術企業、*百家創(chuàng )新型企業,改制成立于2017年8月(簡稱:金嶺股份) ,專業從事數控切削/磨削設備及智能研磨拋光裝備的國家高新技術企業。
金嶺實業集團占地100余畝,擁有研發中心、辦公大樓、聯合廠房近15000平方米、各類設備近200臺,檢測設備近 100 余臺,資產過億元。我們的客戶需要的不僅僅是我們的產品,更需要我們多元化的服務,包括為客 戶提供一站式專機、柔性生產線整體工藝解決方案,新設備融資租賃服務等。
引入了德國PUHLER GmbH作為我們的戰略合作伙伴,派勒是一家總部位于德國漢堡專注于納米研磨智能裝備的科技公司,派勒已將核心產品技術和品牌MAXXMILL授權金嶺股份在中國進行組裝和銷售,為加快推 進中德聯合設計MAXXMILL系列研磨拋光機、高檔數控機床產業化及商業化進程,共同打造“德國技術、 本地智能成套解決方案”。
歡迎您關注我們的微信公眾號了解更多信息
微信掃一掃